改性碱式氯化镁晶须/丁苯橡胶复合材料制备与性能研究

以工业活性轻烧氧化镁粉和盐酸为原料,采用水溶液法制备了碱式氯化镁晶须,继而采用硅烷偶联剂对碱式氯化镁晶须进行改性,然后将其与丁苯橡胶混炼得到改性碱式氯化镁晶须/丁苯橡胶复合材料,研究了改性碱式氯化镁晶须对丁苯橡胶力学性能及热学性能的影响。结果表明：采用水溶液法制备得到的碱式氯化镁晶须结构为Mg₂（OH）₃Cl·4H₂O,呈微细纤维状,分布较均匀,长径比大于20;改性碱式氯化镁晶须的加入,可以改善丁苯橡胶的机械强度和阻燃性能。     

可逆感温变色聚丙烯专用料的制备及性能

通过两步法制备可逆感温变色聚丙烯（PP）专用料，首先将乙烯-辛烯共聚物（POE）与可逆感温变色粉于微型双螺杆挤出机中挤出造粒制备色母料，然后将PP与色母料熔融共混挤出制备可逆感温变色PP专用料。探讨了色母料含量对PP专用料感温变色性能、力学性能、热学性能及微观形貌的影响。结果表明，利用POE与PP良好的相容性，实现了可逆感温变色粉在PP基体中均匀的分散，可逆感温变色PP专用料表现出优异的可逆感温变色性能和冲击性能。     

Modeling and surface texturing on surface roughness in machining LaPO4–Y2O3 composite

In this work, lanthanum phosphate with a 20% yttria (LaPO₄/Y₂O₃) composite prepared by an Aqueous Sol–Gel process is machined using an Abrasive Water Jet Machine (AWJM). The machinability of this composite is studied by varying the input parameters namely Jet Pressure (JP), Stand-Off Distance (SOD), and Traverse Speed (TS) on Surface finish. Garnet of 80 mesh size is used as an abrasive with a flow rate of 85?g/min. The microstructural characterization study reveals the presence of new element YPO₄. This element enhances the machinability and reduced porosity in the composite. Microscopy examinations on the machined surface reveals that partial overlapping at low JP, poor surface finish at high JP and SOD, forged deficiency at maximum SOD and TS. The minimum levels of all input parameters are influenced to obtain acceptable Ra. Atomic Force Microscopy (AFM) on the kerf surface shows micro wear track and peaks. The Multiple Regression Analysis (MRA) is developed for Ra to check the adequacy. From the Analysis of Variance (ANOVA), SOD has a significant effect on Ra with a contribution of 53%. The influence of JP and TS on Ra is found to be 31% and 15%, respectively.     

基于近似测地线的分层次自动铺带轨迹规划方法

自动铺带技术是一种增量制造技术，适用于制造翼面、壁板等大尺寸、小曲率复合材料构件，具有加工成本低、效率高等特点。轨迹规划是自动铺带技术的关键环节，它直接关系到复合材料构件的成型精度与质量。现有的自动铺带轨迹规划方法难以便捷兼顾调控铺放间隙与防止铺放褶皱，保证铺带产品的最终质量。有鉴于此，提出了一种基于近似测地线的分层次铺放轨迹规划方法。主要目标是合理利用预浸带允许变形能力，在防止铺放褶皱产生的前提下，保证相邻带料不产生覆盖，且间隙不超过2.5 mm。首先，研究了铺放间隙的产生与演化规律，给出了几种典型曲面上初始铺放间隙的优化方法。接下来，提出了近似测地线的数学模型与求解格式。然后，基于铺放褶皱的产生机制与铺放间隙的演化规律，确定了近似测地线的测地曲率大小与符号。最后，在双曲面模具以及自由曲面模具上验证了所提出方法的有效性。     

Planetary motion cross bar friction test for application in machining process

This paper describes a new method to evaluate the friction coefficient at the tool-work interface in machining process where high stress and temperature are caused. In order to examine the feasibility of the proposed method, the present report introduces the method and the results obtained only at room temperature. Ti6Al4V, SUS304, AISI1045, FCD 700, FCD 450 and FC300 were used as work materials, while TiN coated carbide tool, TiAlN coated carbide tool and P15 were used as tool materials. The proposed method provided the friction coefficients of different coatings against different work materials, and demonstrated the variability of friction coefficient and the anisotropy of surface roughness.     

某船用柴油机排气管路流-固耦合计算与保温效果研究

对某船用柴油机排气管路的流动与传热过程开展流-固耦合仿真分析。结果表明:受排气管路结构影响，管内流动方向和流速发生变化，局部区域产生明显的回流现象；排气管路外表面温度分布差异较大，平均温度高达534 ℃。为达到柴油机安全设计要求，在排气管路外壁敷设保温材料。分析结果表明:气凝胶纳米材料的保温效果优于硅酸铝纤维材料，在相同的运行条件和使用要求下，气凝胶纳米材料的敷设厚度更薄。     

复合外加剂改性盐石膏的研究

盐石膏的主要成分为无水硫酸钙,其活性差、凝结硬化慢、强度低,需要添加活性剂来激发盐石膏的活性。通过复合外加剂对盐石膏加以改性,并通过XRD和SEM对其作用机理做了分析。结果表明,单掺脱硫石膏和建筑石膏均能缩短盐石膏的凝结时间,建筑石膏的效果较好,但掺量不宜过高。复掺建筑石膏和缓凝剂时,两者比例要控制得当,适宜的建筑石膏和缓凝剂掺量分别为50%和0.10%~0.12%（质量分数）。分析可知,大掺量建筑石膏会增加盐石膏硬化体中二水相和针棒状晶体的含量;缓凝剂掺量的增加,会降低盐石膏硬化体中二水相的含量,棱形晶体增多,从而降低了盐石膏的强度。     

Fabrication and Characterization of Highly Oriented Composite Nanofibers with Excellent Mechanical Strength and Thermal Stability

Here, highly‐oriented poly(m‐phenylene isophthalamide)/polyacrylonitrile multi‐walled carbon nanotube (PMIA/PAN‐MWCNT) composite nanofiber membranes with excellent mechanical strength and thermal stability are successfully produced using electrospinning. It is demonstrated that the cooperation of multi‐walled carbon nanotubes (MWCNT) and high‐speed rotating collection is beneficial to the acquisition of highly oriented fibers and effectively improves the mechanical strength of the membrane along the orientation direction. Specifically, the tensile stress of poly(m‐phenylene isophthalamide)/polyacrylonitrile (PMIA/PAN) membrane is enhanced significantly from 10.6 to 20.7 MPa, benefiting from the highly oriented alignment of the fibers as well as the reinforcing effect of MWCNTs on the fibers. Furthermore, the stressing process of single fiber and fiber aggregates is carefully simulated, and the influence of MWCNTs on the mechanical properties of PMIA/PAN‐MWCNT membranes is analyzed comprehensively, providing a meaningful auxiliary means for the study of mechanical properties. In addition, the composite nanofiber membrane has the advantages of both PMIA and PAN, possessing high temperature resistance, flame‐retardancy, and chemical stability, for an ideal high‐temperature material. In short, the as‐prepared PMIA/PAN‐MWCNT composite membrane with excellent comprehensive property emerges a promising application in many fields, especially in high‐tech.     

碳纤维复合材料修复带缺陷储气井的应力分析及试验研究

针对天然气储气井井管外壁腐蚀现状,采用有限元计算方法,分析不同外壁腐蚀类型、不同腐蚀缺陷尺寸下储气井井管的应力分布、承载极限及疲劳性能;加工带缺陷储气井井管试件,选择碳纤维复合材料湿缠绕法补强修复;对修复后的井管试件进行有限元应力分析,并进行爆破试验和疲劳试验,以充分验证补强方法的有效性;储气井井管的理论分析和性能试验证明,碳纤维复合材料湿缠绕法补强可以有效地修复带外壁缺陷的储气井井管,有效、快捷地解决在役天然气储气井井管外壁腐蚀问题。